(a) Except as provided in subsection (g) of this section, no cigarettes may be sold or offered for sale in this State or offered for sale or sold to persons located in this State unless such cigarettes have been tested in accordance with the test method and meet the performance standard specified in this subsection; and a written certification has been filed by the manufacturer with the State Fire Marshal in accordance with § 7118 of this title, and the cigarettes have been marked in accordance with § 7119 of this title. (1) Testing of cigarettes shall be conducted in accordance with the American Society of Testing and Materials (ASTM) standard E2187-04 "Standard Test Method for Measuring the Ignition Strength of Cigarettes." (2) Testing shall be conducted on 10 layers of filter paper. (3) No more than 25 percent of the cigarettes tested in a test trial in accordance with this subsection shall exhibit full-length burns. Forty replicate tests shall comprise a complete test trial for each cigarette tested. (4) The performance standard required by this subsection shall only be applied to a complete test trial. (5) Written certification shall be based upon testing conducted by a laboratory that has been accredited pursuant to standard ISO/ IEC 17025 of the International Organization for Standardization (ISO), or other comparable accreditation standard required by the State Fire Marshal. (6) Laboratories conducting testing in accordance with this section shall implement a quality control and quality assurance program that includes a procedure that will determine the repeatability of testing results. The repeatability value shall be no greater than 0.19. (7) This section does not require additional testing if cigarettes are tested consistent with this chapter for any other purpose. (8) Testing performed or sponsored by the State Fire Marshal to determine a cigarette's compliance with the performance standard required shall be conducted in accordance with this section. (b) Each cigarette listed in a certification submitted pursuant to § 7118 of this title that uses lowered permeability bands in the cigarette paper to achieve compliance with the performance standard set forth in this section shall have at least 2 nominally identical bands on the paper surrounding the tobacco column. At least 1 complete band shall be located at least 15 millimeters from the lighting end of the cigarette. For cigarettes on which the bands are positioned by design there shall be at least 2 bands fully located at last 15 millimeter from the lighting end and 10 millimeters from the filter end of the tobacco column, or 10 millimeters from the labeled end of the tobacco column for a nonfiltered cigarette. (c) The manufacturer or manufacturers of a cigarette that the State Fire Marshal determines cannot be tested in accordance with the test method prescribed in subsection (a) of this section shall propose a test method and performance standard for such cigarette to the State Fire Marshal. Upon approval of the proposed test method and a determination by the State Fire Marshal that the performance standard proposed by the manufacturer or manufacturers is equivalent to the performance standard prescribed in paragraph (a)(3) of this section, the manufacturer or manufacturers may employ such test method and performance standard to certify such cigarette pursuant to § 7118 of this title. If the State Fire Marshal determines that another state has enacted reduced cigarette ignition propensity standards that include a test method and performance standard that are the same as those contained in this chapter, and the State Fire Marshal finds that the officials responsible for implementing those requirements have approved the proposed alternative test method and performance standard for a particular cigarette proposed by a manufacturer as meeting the fire safety standards of that state's law or regulation under a legal provision comparable to this section, then the State Fire Marshal shall authorize that manufacturer to employ the alternative test method and performance standard to certify that cigarette for sale in this State, unless the State Fire Marshal demonstrates a reasonable basis why the alternative test should not be accepted under this chapter. All other applicable requirements of this section shall apply to such manufacturer or manufacturers. (d) In order to ensure compliance with the performance standard specified in subsection (a) or (c) of this section, data from testing conducted by manufacturers to comply with this performance standard shall be kept on file by such manufacturers for a period of 3 years and shall be sent to the State Fire Marshal upon its request, and to the Office of the Attorney General upon its request. Any manufacturer who fails to make copies of these reports available within 60 days of receiving a written request shall be subject to a civil penalty not to exceed $10,000 for each day after the sixtieth day that the manufacturer does not make such copies available. (e) The State Fire Marshal may adopt a subsequent ASTM Standard Test Method for Measuring Ignition Strength of Cigarettes upon a finding that such subsequent method does not result in a change in the percentage of full-length burns exhibited by any tested cigarette when compared to the percentage of full-length burns the same cigarette would exhibit when tested in accordance with ASTM Standard E2187-04. (f) As of January 1, 2010, and at least every 3 years thereafter, the State Fire Marshal shall undertake a review of the effectiveness of this chapter and report its findings to the legislature. Based upon such review, the State Fire Marshal may recommend legislation to improve the effectiveness of this chapter. The report and legislative recommendations shall be submitted no later than June 30 following the conclusion of each 3-year period. (g) The requirements of subsection (a) of this section shall not prohibit: (1) Wholesale or retail dealers from selling their existing inventory of cigarettes on or after January 1, 2009, if the wholesale or retailer dealer can establish that state tax stamps were affixed to the cigarettes prior to January 1, 2009, and if the wholesale or retail dealer can establish that the inventory was purchased prior to January 1, 2009, in comparable quantity to the inventory purchased during the same period of the prior year. (2) The sale of cigarettes solely for the purpose of consumer testing. For purposes of this subsection, the term "consumer testing" shall mean an assessment of cigarettes that is conducted by a manufacturer (or under the control and direction of a manufacturer), for the purpose of evaluating consumer acceptance of such cigarettes, utilizing only the quantity of cigarettes that is reasonably necessary for such assessment, and in a controlled setting where the cigarettes are either consumed on-site or returned to the testing administrators at the conclusion of testing. (h) This chapter shall be implemented in accordance with the implementation and substance of the New York Fire Safety Standards for Cigarettes.
‹ Prev All Delaware sections Next ›
Lexace provides legal information, not legal advice, and no attorney–client relationship is created. Statute text is provided for general information and may not reflect the most recent amendments; verify against the official state code.